Daysailer Sailboats for sale in Indiana

1-4 of 4

Sort By

1987 Seaward 24

1987 Seaward 24

$7,499

Fort Wayne, Indiana

Year 1987

Make Seaward

Model 24

Category Daysailer Sailboats

Length 24'

Posted Over 1 Month

1987 Seaward 24 Ready to sail beautiful 1987 Seaward 24. Inventory includes autopilot, Bimini (2015), VHF, roller furling genoa, two batteries and custom cockpit table. Antifouling paint competed in 2015. Comes with trailer and 2004 Nissan 9.8 four-stroke engine professionally maintained. Only 2f draft, sails in light and heavy weather with confidence. The basic design of this boat is still in production. Take advantage of this very unique strongly built boat that will give you and your family much joy.

Rebel 16 Mark II Sailboat with Aluminum Trailer

Rebel 16 Mark II Sailboat with Aluminum Trailer

$999

Angola, Indiana

Year -

Make -

Model -

Category Daysailer Sailboats

Length 16.6'

Posted Over 1 Month

Stable fiberglass sailing boat carries six people (or 1170 pounds). Includes trailer, full rigging, and TWO suits of sails. One suit of sails is in like new condition, the other set is in very good condition. Serial number 1929 (built in late sixties to early seventies I believe). The centerboard swings up into the cockpit, so you can change the depth to dock in shallow water. The rudder also swivels up if it hits an obstruction. The trolling motor in the photos is not included. There is, however a permanent motor mount on the stern. The boat will take up to a 5hp motor, but my 30lb. thrust trolling motor drives it around just fine. The boat is located on West Otter Lake, Angola, IN. Buyer with the selling price in cash or Pay Pal payment can drive it away. (Trailer takes an 1 7/8" ball hitch.) The following article from Sailing Magazine gives a great description of Rebel sailboats. You can access the original on SailingMagazine.net. Rebel 16 2008 January 8 By Staff This nimble and tough classic is perfect for a daysail or a day of racing This year the boat that holds claim to being America's first production fiberglass one-design will celebrate its 60th birthday. That the boat is still in production makes this milestone that much more remarkable. In 1948, fresh out of the Navy, Ray Greene began building a 16-foot family daysailer out of his Toledo, Ohio, shop using a revolutionary new material called fiberglass. The design of the boat was based on lines drawn by a local high school drawing instructor by the name of Alvin Younquist. With its wide, 6-foot, 7-inch beam and 110-pound steel centerboard the stable little boat known as the Rebel soon became a hit on the Midwest's inland lakes. And while Greene said he never intended to create a racer, thanks to the boat's performance-courtesy of a large 120-square-foot main and 46-square-foot jib on a fractional rig-it wasn't long before a competitive structure was built around the boat. By 1952 a class association had been firmly established and by 1963 the class boasted 138 active members. Not bad. Fleets started popping up across the Midwest, south into Kentucky and all the way down to Texas. Meanwhile, class members could be found sailing the inland lakes of the Eastern Seaboard from New York to Florida. After 25 years of building the Rebel, with more than 3,000 hulls produced, Greene was ready to call it quits and sold the works to a group of Chicago investors. Production of the Rebel continued at a steady pace during the 1970s, and was done under a number of names: Melling Tool Co., Rebel Industries and finally Spindrift One Designs. After Spindrift folded, the Rebel moved to Michigan in 1988 when Nickels Boat Works of Fenton took over with the production of the Mark V model. Nickels continues to build the Rebel, offering buyers a choice of a daysailer version for $9,860 or the optimum racing version for $11,872 less sails and trailer. A stainless steel centerboard now comes standard with the Rebel. Nickels also continues to be a great source for parts and accessories, as well as information, on the Rebel. One tough Rebel While there have been reports of problems with the foam flotation on older boats becoming waterlogged, that has been less of a problem on boats from the 1970s and later. Other than that, a buyer of a used Rebel should find few issues with the condition of this durable little boat. Indeed, boats 25 years and older will still top regatta leaderboards. "They're well made, very rugged boats that will last forever," said Al Vorel, National Rebel Association Commodore, who has been racing the same boat, No. 3914, for almost 20 years. "You don't have to run out every 5 to 10 years to buy a new boat." This is one of the reasons for the longevity of the class. Boats tend to stay in the family, passed down from parent to child, with the younger generations wanting to keep the racing going. "My mother races, and my daughter sometimes races, so there are times we'll have three generations on the course," Vorel said. This also, of course, keeps a lot of boats off the market, and finding a used Rebel can be a bit of a challenge. But thanks to the Internet, it's possible to locate a few sellers. Prices can vary from just under $1,000 for an older boat in need of some work to $3,000 or more for a later model. Buyers can typically expect to pay in the neighborhood of $1,500 for a pre-Nickels-era boat in good shape. We were fortunate enough to find a late 1970s Rebel listed for sale on www.craigslist.org. Better yet, the seller was within trailering distance. The offer on the boat was $1,400, so we drove out to take a look. The boat was well cared for, kept under a roof winters, and showed no structural damage. Other than some algae stains and scuff marks the finish looked good, and all the gear was there, including the main and jib, which the owner said he bought new about seven years ago. We did see some possible issues, including a rusty, pitted centerboard and a wooden rudder that looked to have some rotting. So we offered to pay the full $1,400 if the owner threw in the trailer, which he originally wanted an extra $200 for. The deal was closed and we drove off with the Rebel in tow. Rebel with a cause With the boat parked in our yard the first item of business we wanted to take care of was the rusty centerboard. Nickels offers a stainless steel replacement board, and we could picture how sweet the boat would look with a shiny new stainless fin. Unfortunately, these centerboards run close to $1,000; more than two-thirds the cost of the entire boat. So such an extravagant purchase didn't make much sense. Instead we set about rehabilitating the old board. We removed, with a bit of difficulty, the 110-pound board and set in on sawhorses. The first step was to remove the old paint using paint stripper, then power sanding. We then slathered on some Duro Naval Jelly to remove the rust, wiping down everything with paper towels then finishing up with a clean, acetone-soaked rag. Next, we filled in the pits and hollows with West Marine Surfacing Putty, and sanded everything smooth. We made certain the blade was fair by running a straight edge along the board. We also further faired the rounded leading edge of the board to within the class rule limits, which prohibit tapering less than 1/16th of an inch and more than one inch in from the leading edge. We then primed the board with several coats of Interlux Primocon primer, which when dried we wet sanded with 400-grit paper, and finished with a couple coats of Interlux VC-17m Extra bottom paint. With the centerboard done, we then turned to the rudder. An ice pick determined the wood was beginning to rot near the lower trailing edge. We probably could have rehabilitated the rudder as well, but since we had saved some money by not replacing the centerboard we decided to spring for a new rudder. We opted for a fiberglass blade, supplied by Nickels for $375. This cost covered just the blade, as the original aluminum rudder cheeks and hardware were still in good shape. While we were on the phone with Nickels, we decided to order all new running rigging to replace the weathered lines the boat came with. This included lines for the cunningham, boom vang, centerboard system, as well as sheets and halyards for both main and jib. The total for 112 feet of ¼-inch line and 105 feet of 5/16-inch line came to $100. Next we took a closer look at the standing rigging. The spars showed no defects, and with a bit of metal polish and elbow grease the rotating mast, boom and aluminum whisker pole looked good as new. The 1-by-9 stainless steel shrouds and forestay also showed no visible defects. We did, however, find the diamond stays on the mast to be tuned rather tight. According to the North Sail's One-Design tuning guide for the Rebel, an overly tight diamond can limit fore and aft mast bend, and can even cause negative pre-bend, where the mast bends forward at the tip. Since we want to have a competitive boat, we loosened the diamond tension and will readjust after doing some sea trials. As we said, we ultimately wanted to race our Rebel and didn't want a slow boat. So obviously the 7-year-old suit of sails had to go. This would be our biggest expense, and a new suit of sails would alone exceed the original cost of the boat. A new main and standard jib (a light air jib is also available) from North Sails set us back $1,615, which included $20 for class royalties but not shipping. Certainly this was a blow to our budget, but we rationalized it by thinking about the fun we would be having with some close racing come summer. Our last order of business was getting our bottom clean and smooth. We first scrubbed the hull down with a detergent then wet sanded everything below the rails to a slick surface with 1,200-grit paper. After a rinse and wipe down with the hose and clean towels we were satisfied we had a slick bottom. We finished off by treating all our hardware and moving bits to a little McLube Sailkote spray. We now have what we feel will be a contender on the course for our racing crew of two. Yet, with the roomy Rebel cockpit that can seat six, we're also looking forward to some lazy summer daysailing when friends and family show up. Either way, we'll certainly get our money's worth from this tough but nimble little classic. LOA 16' 1.5" LWL 15' 10" Beam 6' 7.5" Draft 3' 4" Weight 700 lbs, Sail area 166 sq. ft.

1975 Catalina 22 Pop Top Sailboat and Trailer - Project

1975 Catalina 22 Pop Top Sailboat and Trailer - Project

$859

Martinsville, Indiana

Year 1975

Make Catalina

Model 22

Category Daysailer Sailboats

Length 22.0

Posted Over 1 Month

1975 Catalina 22 Pop Top Project Sailboat and Trailer The Catalina 22 is a popular sailboat produced by Catalina Yachts. Its hull measures 21 foot 6 inches (6.55 m), which is rounded up to 22 feet (6.7 m) for use in the model's name. First produced in 1968, it is one of the longest continuously produced sailboats in the world...Over 15000! Parts, videos and know-how are abound on the net 2005 last time previous owner had boat in water. I have never had boat in the water or was able to work on her. 2005 was the last time I was inside the cabin before preparing this listing for ebay. She has been closed up for ten years and is dirty in and out. I sprayed Windex in a few areas inside and dirt just wiped off with no scrubbing. Water, at one time, intruded around the forward hatch. Has complete set of interior cushions in gold plaid pattern. Most are in surprising good condition. NO SMELLS. One has a 1.5x1.5 inch hole in fabric that isn't seen when in place. 1 or 2 have an area of cracking vinyl. In all the noted exceptions, I don't think they would be seen or stop you from sailing PREVIOUS OWNER'S DESCRIPTION: '75 Catalina 22 pop top w/trailer • fair condition - Project boat • Swing Keel • Pop top • Sail Inventory: 2 mains, Jib (Marked San Juan works w/Cat 22s) and 150 Furling I think all are usable • Scupper upgrade in transom • Ablative paint on hull and keel • Never in salt water • Needs good cleaning • I know of no problems with the swing keel • No known leaks around keel pin • Comes with 2 Rudders. Usable but not perfect • Port side blemish in the gel coat • One pop top support needs to be re-bedded • Front hatch needs the frame reinstalled and sealed • Soft spot forward of hatch • Crack in cabin threshold but does not affect anything much • Cracks and crazing in the deck gelcoat that need filling • One stanchion base needs to be re-bedded • Small dent/crack in mast near stays, like pinched on one side at the spreaders. When raising the mast, one of the stays was caught and pulled the spreader forward. See photo. A pontoon boat repair guy told me that a braze could patch for about $25 • Needs halyards but I would get all new running rigging • Replace Hatch Boards or just cut a Plywood Hatch • Standing rigging, I am no judge but it worked when last used and it has been out of the elements since. • The forestay also has a quick-release lever purchased from Catalina Direct, along with quick-release pins for quicker and easier mast- raising and lowering. Those parts are, of course, stainless steel. • Will also include a sliding galley out of a 1984 Cat 22. It slides under the cockpit starboard seating when not in use. It has a faucet, sink, water fresh water holding tank, a drawer and a place for a small portable propane stove. I was going to sell it separately on ebay. They normally go from 150-200. TRAILER • Trailer in good shape, but could use some paint• Has 10 ft extension• Has surge brake system used for two trips since it was installed• Has Buddy Bearings• New load range 'C' tires were put on in Spring of 2010. 63 Miles total mileage as boat was towed from one of our rental homes to our house in Martinsville. No cracks or aging seen.• Extra duty bunks BTW: Good used trailers for sailboats are hard to come by. Have clear titles for boat and trailer. I have described everything I know about her to the best of my ability but I am no sailor. Somethings may be better and others may be worse. She is a project boat and sold as is. This is for local Pickup in Martinsville, Indiana (Just south of Indianapolis) An immediate non-refundable PayPal deposit of $200 is required upon purchase. Balance due in CASH when picked up. No checks or money orders of any kind. Pickup within 7 business days of end of listing. This is not an auction. Will be happy to answer questions Thanks for looking and your interest

1975 Catalina 22 Pop Top Project Sailboat and Trailer

1975 Catalina 22 Pop Top Project Sailboat and Trailer

$1,099

Martinsville, Indiana

Year 1975

Make Catalina

Model 22

Category Daysailer Sailboats

Length 22.0

Posted Over 1 Month

1975 Catalina 22 Pop Top Project Sailboat and Trailer The Catalina 22 is a popular sailboat produced by Catalina Yachts. Its hull measures 21 foot 6 inches (6.55 m), which is rounded up to 22 feet (6.7 m) for use in the model's name. First produced in 1968, it is one of the longest continuously produced sailboats in the world...Over 15000! Parts, videos and know-how are abound on the net 2006 last time previous owner had boat in water. I have never had boat in the water or was able to work on her. Selling because soon after buying her, a heart problem took the wind out of my sails. Thought I would sooner or later, but unfortunately I will never be able to sail her. The following is description of previous owner: '75 Catalina 22 pop top w/trailer • fair condition - Project boat • Does not include motor (One available for a separate purchase) • Swing Keel • Pop top • Has sails, usable • Scupper upgrade in transom • Ablative paint on hull and keel • Complete set of interior cushions in gold plaid pattern are in decent condition • Never in salt water • Needs good cleaning • I know of no problems with the swing keel • No known leaks around keel pin • Rudder is good, but not perfect • Port side blemish in the gel coat • One pop top support needs to be re-bedded • Front hatch needs the frame reinstalled and sealed • Small crack in cabin threshold but does not affect anything much • Some cracks and crazing in the deck gelcoat that need filling • One stanchion base needs to be re-bedded • Small dent/crack in mast near stays, like pinched on one side at the spreaders. When raising the mast, one of the stays was caught and pulled the spreader forward. It pushed into the mast, and the mast has a small crack in it of approx. one inch. A aluminum boat repair guy told me that a weld could patch for $25 • Needs halyards but I would get all new running rigging • Replace Hatch Boards or Just cut a Plywood Hatch • The forestay also has a quick-release lever purchased from Catalina Direct, along with quick-release pins for quicker and easier mast- raising and lowering. Those parts are, of course, stainless steel. TRAILER • Trailer in good shape, but could use some paint• Has 10 ft extension• Has surge brake system used for two trips since it was installed• Has Buddy Bearings• Good tread on tires• Extra duty bunks BTW: Good used trailers for sailboats are hard to come by. Have titles for boat and trailer She is a project boat and is sold as is. I will cannot entertain low balling, consider trades, or Ebayers with negative feedback. This is for local Pickup in Martinsville, Indiana, just south of Indianapolis. An immediate non-refundable PayPal deposit of $200 is required upon purchase. Balance due is to be paid within 7 business days in cash only. No checks or money orders of any kind. You may pay balance via PayPal prior to picking up the boat. This is not an auction. Will be happy to answer questions Thanks for looking