Custom Cutter boats for sale in Florida

1982 Custom Treworgy Pilothouse Cutter

$49,000

Clearwater, Florida

Year 1982

Make Custom

Model Treworgy Pilothouse Cutter

Category Cutter

Length 34'

Posted Over 1 Month

1982 Custom Treworgy Pilothouse Cutter This pilothouse cutter is truly one of a kind. Designed by Mark Treworgy and built by Treworgy Boat Building in NE Florida, with steel construction to ensure that she was tough and strong. Awlgrip Arista Blue hull. Not only is she rugged, but she will turn heads. Her pilothouse is offset by a graceful hull design, and the low profile makes her look anything but "boxy" (as some pilothouse boats tend to do). Her owner has sailed both the Atlantic and Pacific oceans aboard her, and she now sits in St. Augustine, FL, awaiting her next adventure. Her hull was plated of 3/16" and bottom of keel with 1/2" steel with substantial framing, with 3000 lbs. of lead ballast (cast to shape and anchored). Her cabin is aluminum (isolated from the steel). Mark Treworgy designed her to be rugged and strong, yet comfortable inside. She can be steered from inside the pilothouse or from the cockpit, her galley is sizeable, and v-berth functions as a double berth or twin singles. Interior joinery and craftsmanship is superb. Among her equipment: 2 VHF Radios Benmar 21 Autopilot AIS Receiver 2 GPS systems, Garmin Signet wind instrument Signet knotlog Signet Fathometer Scanmar Monitor waindvane with aux. tiller pilot Icom SSB 220 Amp hour house battery bank with space for an additional 220 amp hour Separate starting battery 3 burner propane range and oven Crosby 12 B Refrigeration More-than-ample storage Dickerson heating system 2 fire extinguishers 2 electric bilge pumps and 1 manual Bilge blower Nilson electric windlass 35 lb. CQR

1987 Custom 48 Cutter

$144,900

Jacksonville, Florida

Year 1987

Make Custom

Model 48 Cutter

Category -

Length 48'

Posted Over 1 Month

1987 Custom 48 Cutter Started in 1987; completed and launched in 2004. Approx. 200 hours, new toilet, new batteries. Unusual layout, aft cockpit with ample room in interior includes aft stateroom. The forward v-berth stateroom is quite large, just aft is the head/shower. Seating in the salon and also a table with seating. Galley is rear salon starboard side, entry to master is aft port side. Exterior: Cutter rig with stern cockpit. Hull; faceted displacement type with fin keel and rudder, raked stern, whale-back sheer and reversed transom stern. Dock; flush main deck from bow to stern, recessed cockpit amidships and at stern, low profile trunk cabin style with a great deck area.

2006 Custom-Made Steel Cruising Cutter

$283,864

Fort Lauderdale, Florida

Year 2006

Make Custom-Made

Model Steel Cruising Cutter

Category Sailboats

Length 47'

Posted Over 1 Month

2006 Custom-Made Steel Cruising Cutter This vessel is a great ocean going cruising yacht. She is exceptional in almost all areas. The attention to detail, quality of build and standard of equipping in terms of reliability and safety are close to unique. Clearly the owners experience and knowledge as a professional seamen and engineer are the major factors distinguishing this custom built yacht.

2006 Custom-Made Cruising Cutter

$284,382

Fort Lauderdale, Florida

Year 2006

Make Custom-Made

Model Cruising Cutter

Category Sailboats

Length 47'

Posted Over 1 Month

2006 Custom-Made Cruising Cutter This vessel is a great ocean going cruising yacht. She is exceptional in almost all areas. The attention to detail, quality of build and standard of equipping in terms of reliability and safety are close to unique. Clearly the owners experience and knowledge as a professional seamen and engineer are the major factors distinguishing this custom built yacht.

1987 Custom Cutter

$144,900

Jacksonville, Florida

Year 1987

Make Custom

Model Cutter

Category Sailboats

Length 48'

Posted Over 1 Month

1987 Custom Cutter Started in 1987; completed and launched in 2004. Approx. 200 hours, new toilet, new batteries. Unusual layout, aft cockpit with ample room in interior includes aft stateroom. The forward v-berth stateroom is quite large, just aft is the head/shower. Seating in the salon and also a table with seating. Galley is rear salon starboard side, entry to master is aft port side. Exterior: Cutter rig with stern cockpit. Hull; faceted displacement type with fin keel and rudder, raked stern, whale-back sheer and reversed transom stern. Dock; flush main deck from bow to stern, recessed cockpit amidships and at stern, low profile trunk cabin style with a great deck area.

43' Steel Sailboat Hull for finishing and bluewater cruising.

$35,000

Palatka, Florida

Year 2016

Make Custom

Model George Sutton Dished Steel Cutter

Category Cruiser Motorcycles

Length 43.0

Posted Over 1 Month

43 foot LOD Dished steel, George Sutton designed Custom made by a professional shipyard. This vessel has never been launched and is awaiting completion. Interior stringers are predrilled for easy bolting of interior. Wear points, Chainplates, Stanchion bases, Hatch hinges, and mooring cleats are all welded stainless steel to prevent rust staining by lines etc. wearing through the paint. I purchased the vessel from the welder. vessel was white blasted prior to having 5 + coats of epoxy sprayed. I rolled on over 20 gallons of additional epoxy coats. In addition to Spars, sails, rigging and interior woodwork, the Vessel needs engine (Designed for 85=100 HP diesel), needs prop and prop shaft. I have a transmission that probably needs rebuilt. Also it has 10,000 pounds of lead ballast in keel, 200 gallons of fuel tankage also built into the keel. Engine bed mounts welded in over the bilge. Bronze steering quadrant. Stainless Steel destroyer wheel.This hull is very well built and would make an ideal bluewater cruiser or circumnavigator. Priced at under half of the cost of a new hull build out, this boat is a great project.